| ABSTRACT (IN CHINESE) | 第4-6页 |
| ABSTRACT | 第6-8页 |
| CHAPTER 1 INTRODUCTION | 第11-24页 |
| 1.1 THE PURPOSE AND SIGNIFICANCE OF RESEARCH | 第11-14页 |
| 1.2 AASCM COMPOSITION, STRUCTURE AND PROPERTIES | 第14-16页 |
| 1.3 AASCM EXCITATION MECHANISM | 第16-18页 |
| 1.4 AACM RESEARCH STATUS | 第18-20页 |
| 1.5 AASCM WORK PROPERTIES RESEARCH STATUS | 第20-22页 |
| 1.6 RESEARCH CONTENTS | 第22-24页 |
| 1.6.1 Current status of AASCM workability existing problems | 第22页 |
| 1.6.2 The main contents of the thesis | 第22-24页 |
| CHAPTER 2 RAW MATERIALS AND TEST EQUIPMENT | 第24-36页 |
| 2.1 INTRODUCTION | 第24页 |
| 2.2 EXPERIMENTAL RAW MATERIAL | 第24-30页 |
| 2.2.1 Slag | 第24-26页 |
| 2.2.2 Sodium hydroxide | 第26-27页 |
| 2.2.3 Sodium Silicate | 第27-30页 |
| 2.3 TEST MIX PROPORTION AND SELECTION OF RAW MATERIALS | 第30-32页 |
| 2.4 TEST EQUIPMENT AND TEST PROCEDURES | 第32-36页 |
| CHAPTER 3 THE INFLUENCE OF KEY PARAMETERS ON THE SETTING TIMEOF AASCM | 第36-47页 |
| 3.1 INTRODUCTION | 第36-37页 |
| 3.2 THE RESULTS AND ANALYSIS OF THE INITIAL AND FINAL SETTING TIME | 第37-46页 |
| 3.2.1 The effect of the modulus of sodium silicate solution | 第37-41页 |
| 3.2.2 The effect of the content of sodium oxide | 第41-43页 |
| 3.2.3 The mechanism analysis of the content of sodium oxide and modulus ofsodium silicate solution on initial setting time | 第43-44页 |
| 3.2.4 Effect of the temperature | 第44-46页 |
| 3.3 CHAPTER SUMMARY | 第46-47页 |
| СHAPTER 4 AASCM SETTING TIME FORMULA FITTING | 第47-61页 |
| 4.1 INTRODUCTION | 第47页 |
| 4.2 AASCM INITIAL SETTING TIME FORMULA FITTING | 第47-53页 |
| 4.2.1 Initial setting time under the influence of sodium silicate modulus formulafitting | 第47-48页 |
| 4.2.2 Initial setting time under the influence of sodium oxide content formulafitting | 第48-50页 |
| 4.2.3 Formula fitting of complex influence of sodium silicate modulus and sodiumoxide content on initial setting time | 第50-52页 |
| 4.2.4 Initial setting time under the influence of temperature fitting formula | 第52-53页 |
| 4.3 FORMULA FITTING OF FINAL SETTING TIME OF AASCM | 第53-59页 |
| 4.3.1 Formula fitting of final setting time under the influence of sodium silicate | 第53-54页 |
| 4.3.2 Formula fitting of final setting time under the influence of sodium oxidecontent | 第54-56页 |
| 4.3.3 Formula fitting of final setting time under the influence of sodium silicatemodulus and sodium oxide content of the composite effect | 第56-58页 |
| 4.3.4 Formula fitting of final setting time under the influence of temperature | 第58-59页 |
| 4.4 CHAPTER SUMMARY | 第59-61页 |
| CHAPTER 5 FLUIDITY OF AASCM AND ITS FORMULA FITTING | 第61-70页 |
| 5.1 INTRODUCTION | 第61页 |
| 5.2 THE EFFECTS ON FLUIDITY AND FORMULA FITTING | 第61-66页 |
| 5.2.1 The effects on fluidity and formula fitting of sodium silicate modulus | 第61-64页 |
| 5.2.2 The effects on fluidity and formula fitting of modulus of sodium oxide | 第64-66页 |
| 5.3 THE EFFECT OF TEMPERATURE ON FLUIDITY AND FORMULA FITTING | 第66-68页 |
| 5.4 CHAPTER SUMMARY | 第68-70页 |
| CONCLUSION (IN CHINESE) | 第70-72页 |
| CONCLUSION | 第72-75页 |
| REFERENCES | 第75-79页 |
| ACKNOWLEDGEMENT | 第79-81页 |
